Sponsored Content
8
Free Member
Send PMRiverhead, NY - USA
Joined: 12/13/2004
Posts: 64
Vette(s): 1981 Cream exterior, camel interior. Looks great, runs good.
Hey guys,
How do you remove the tint from your windshield and also get the sticky glue off the window? Someone sugguested gasoline? Hmmmm! Don't know? Any suggestions?
June
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
SPONSOR AD:: (Our Sponsors help support Vette Registry)
e
Lifetime Member
Send PMLanoka Harbor, NJ - USA
Joined: 12/21/2006
Posts: 2191
Vette(s): 1975 metallic blue coupe with t-tops,L48, t/t steering, black leather interior. 1990 L98, white/red leather interior, auto,a/c
you can use rubbing alcohol or acetone (nail polish remover). alcohol
would be better as acetones smell can get to you and plus can damage
plastics. they do have adhesive removers at the auto stores too. as far
as gasoline goes i wouldn't even consider that as the fumes can ignite
also. then again that would remove the adheasive, the glass, the car,
YOU,etc...
eddie20875 2007-05-21 15:47:02
LIFETIME MEMBER #97
THE DYNAMIC DUO
THE DYNAMIC DUO
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
Or try hot soapy water first before trying solvents.
Normally window tint is applied by spraying soapy water on the glass and the adhesive side of the tint for positioning purposes. Then the tint is squeegeed to push the liquid out to let the adhesive cure. So I believe the adhesive may be water soluble.
GEN III 5.7L "LS6" Engine swap
TKO500 5 spd.
3.54 Dana 44
'69 "N11" Sidepipes
Borgeson Steering Box
Born 8/1981
Sequence #3975
Click here to see more pics of my Vette on CarDomain.
Lifetime Member #26
Borgeson Steering Box
Born 8/1981
Sequence #3975
Click here to see more pics of my Vette on CarDomain.
Lifetime Member #26
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
Free Member
Send PMCramerton, NC - USA
Joined: 8/22/2006
Posts: 1094
Vette(s): black 1982 coupe slate gray interior, 350 crossfire, 1985 fuel pump, Steeroids R&P conversion
When I got my 82, the previous owner had put tint film on the rear window. I'm sure it looked "OK" in the beginning but it was showing its age. I had it "steamed" off, no scraping, no glue, no elbow grease. The guy did it for me for $50.00 which I was glad to pay not to have to crawl into the luggage area on my back. I did cover my rear compartment doors with plywood when I took it to the tint shop though, didnt want bubba to put his knee through my compartment doors. Good luck with the removal, it's a pain to remove by most methods.
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
e
Lifetime Member
Send PMLanoka Harbor, NJ - USA
Joined: 12/21/2006
Posts: 2191
Vette(s): 1975 metallic blue coupe with t-tops,L48, t/t steering, black leather interior. 1990 L98, white/red leather interior, auto,a/c
[QUOTE=Darryl81]Or try hot soapy water first before trying solvents.
once the glue sets water doesn't help. they put decals on our trucks at work with the soap and water. taking them off is a pain. steam would do it as it will loosen the glue and you basically wipe any excess glue away. maybe one of them hand held steam cleaners like they have on tv might work. daughter had to remove some from her car to pass state insp. she said it peeled off in large pieces but left the glue. she used alcohol.
Normally window tint is applied by spraying soapy water on
the glass and the adhesive side of the tint for positioning purposes.
Then the tint is squeegeed to push the liquid out to let the adhesive
cure. So I believe the adhesive may be water soluble.
[/QUOTE]once the glue sets water doesn't help. they put decals on our trucks at work with the soap and water. taking them off is a pain. steam would do it as it will loosen the glue and you basically wipe any excess glue away. maybe one of them hand held steam cleaners like they have on tv might work. daughter had to remove some from her car to pass state insp. she said it peeled off in large pieces but left the glue. she used alcohol.
LIFETIME MEMBER #97
THE DYNAMIC DUO
THE DYNAMIC DUO
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
r
The hand held steamer will work. Any stubborn
areas can be removed with a Windex and a razor blade. If you rear
window has defrost elements then DO NOT use the razor blade.
Scott
Scott
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
k
Free Member
Send PMGreat Bend, KS - USA
Joined: 5/20/2007
Posts: 13
Vette(s): White 1977 coupe, red interior, automatic
I think Wal-Mart sell window tint remover in the automotive section, but I don't know how well it works.
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
8
Free Member
Send PMRiverhead, NY - USA
Joined: 12/13/2004
Posts: 64
Vette(s): 1981 Cream exterior, camel interior. Looks great, runs good.
Thanks guys, I knew my C3 folks had the answers. I'll try the alcohol, steam and find a Wal-Mart also. I have an '81 with the tint on the front windshield, which is annoying now. The tint on the windows came off easily but left some glue. I'll let you know what works. 
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
I ran into the guy that tinted my windows today. So for the heck of it I asked him how he removes the adhesive residue. He said it's a PITA, but he uses a razor blade and scrapes the glue off that way. Not a fun job.
Now on the back window with rear defrost, Do this on a hot sunny day.(I found this interesting) he said that he uses a old piece of the clear backing that window tint comes bonded to. Cuts it to size of the window, sprays down the backing and the window with soapy water. Let it cling to the window surface in which the adhesive is on. No squegee'in. Let it get hot and then periodically try pulling the clear backing off. If the adhesive comes of the window and clings to the clear backing, the glass is hot enough. If not, let it bake in the sun for awhile longer.
So this is from a guy that does it for a living. Whether it's right or wrong, I don't know.
Or he suggested going out to your car at 2 am and throw a rock through the window, and let the insurance company pay for a new window. 
GEN III 5.7L "LS6" Engine swap
TKO500 5 spd.
3.54 Dana 44
'69 "N11" Sidepipes
Borgeson Steering Box
Born 8/1981
Sequence #3975
Click here to see more pics of my Vette on CarDomain.
Lifetime Member #26
Borgeson Steering Box
Born 8/1981
Sequence #3975
Click here to see more pics of my Vette on CarDomain.
Lifetime Member #26
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
in Forum: Corvette Car Care
Sponsored Content