Sponsored Content
Free Member
Send PMCambridge, MN - USA
Joined: 5/25/2012
Posts: 1
Vette(s): Red '91 Coupe. 5.7 liter L-98, Tuned Port Injection. Mods Include Magniflow Cat-back exhaust with LT-1 tips, throttle-body air-splitter, K&N air filter with high-flow cover, Hypertech high capacity coil, Hypertech Thermo-Master chip.
OK1 I'm in need of a replacement battery for my '91 L98 Coupe. What is the easiest way R&R?
John Vaughan
'91 Red C-4 Coupe
"Drive It Like You Stole It! - Show It Like You Own It!"
'91 Red C-4 Coupe
"Drive It Like You Stole It! - Show It Like You Own It!"
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
SPONSOR AD:: (Our Sponsors help support Vette Registry)
b
You have to remove the gill panel behind the front tire. I did mine last year.
1) turn wheels to left & open hood
2) remove 5 screws holding rear of fender well to access panel
3) remove upper bolt on top of access panel
4) loosen (don't remove) lower bolt; along the bottom of the panel is an indent just large enough for an open end wrench.
2) remove 5 screws holding rear of fender well to access panel
3) remove upper bolt on top of access panel
4) loosen (don't remove) lower bolt; along the bottom of the panel is an indent just large enough for an open end wrench.
Shouldn't take more than 10 minutes to remove it.
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
The above info provided by Brocky is how to proceed :
For a short video on this issue follow this link.
|UPDATED|10/27/2012 3:14:27 AM (AZT)|/UPDATED|
Also, when you put the side panel back on make sure your door is not going to jam on it. Check the alignment with door and hood.
nothing to it .....
|UPDATED|10/27/2012 3:14:27 AM (AZT)|/UPDATED|
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
Just did mine last week, the video is dead on and it only took me about 15 minutes to do it all and put it back together.... Easier than it looks..
Allan Brenneis Nashville Tn. 1990 Polo Green Coupe Saddle Interior Chrome ZR-1 Rims http://www.c4vetteregistry.com/member_uploads/14501_14600/14572/image2014329104347r.jpg
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
Trooper said: .... Easier than it looks..
As long as you have the torx bit ( I don't recall which one it is) edit: The video says "T25 bit". Might be that big. BWTFDIK
|UPDATED|10/28/2012 9:54:28 AM (AZT)|/UPDATED|
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
Yea, having torque bits wold help..... a little bit.....
Allan Brenneis Nashville Tn. 1990 Polo Green Coupe Saddle Interior Chrome ZR-1 Rims http://www.c4vetteregistry.com/member_uploads/14501_14600/14572/image2014329104347r.jpg
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
b
Watched the video on youtube. Didn't know Bill Clinton had a Vette
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
in Forum: C4 Electrical, Body and Interior
Sponsored Content