Sponsored Content
I'm installing a new carb (from the original qjet) and the throttle cable is about 1 inch too long.
Can this be shortened?
Can this be shortened?
|B|76 X coupe |/B|
#s match - Classic White - Buckskin
|IMG|http://webpages.charter.net/equestrian/76x.gif |/IMG|
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
SPONSOR AD:: (Our Sponsors help support Vette Registry)
Lifetime Member
Moderator
Send PMModerator
Duncanville, TX - USA
Joined: 11/8/2003
Posts: 22716
Vette(s): #1-1974 L-48 4spd Cp Med Red Metallic/Black deluxe int w/AC/tilt/tele./p/w-p/b/
Am-Fm/map light National/Regional/Chapter NCRS "Top Flight"
#2-1985 Bright Red/Carmine Cp.L-98/auto
Member: NCRS, NCRS Texas, Corvette Legends of Texas
The cable itself can't be shortened, but you should be able to move/change the bracket. What carb are you using? You can get "universal" type brackets @ parts stores. 
Joel Adams
C3VR Lifetime Member #56 
My Link 
(click for Texas-sized view!) NCRS
"Money can't buy happiness -- but somehow it's more comforting to cry in a CORVETTE than in a Kia"
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
I've looked around at other brackets, but none would move the cable enough.
I've tried a holley and demon, both are the same and my pedal is not bent and I can't move the bracket at all.
I've heard a bubba fix would be to put a few split shot fishing weights on the cable by the pedal to change the contact point - anything else?
|UPDATED|1/26/2005 9:21:43 PM (AZT)|/UPDATED|
I've tried a holley and demon, both are the same and my pedal is not bent and I can't move the bracket at all.
I've heard a bubba fix would be to put a few split shot fishing weights on the cable by the pedal to change the contact point - anything else?
|UPDATED|1/26/2005 9:21:43 PM (AZT)|/UPDATED|
|B|76 X coupe |/B|
#s match - Classic White - Buckskin
|IMG|http://webpages.charter.net/equestrian/76x.gif |/IMG|
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
s
Look at Summit at the edelbrock throttle cable brackets and see if you like them. I'm useing a chrome one.
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
Lifetime Member
Moderator
Send PMModerator
Duncanville, TX - USA
Joined: 11/8/2003
Posts: 22716
Vette(s): #1-1974 L-48 4spd Cp Med Red Metallic/Black deluxe int w/AC/tilt/tele./p/w-p/b/
Am-Fm/map light National/Regional/Chapter NCRS "Top Flight"
#2-1985 Bright Red/Carmine Cp.L-98/auto
Member: NCRS, NCRS Texas, Corvette Legends of Texas
| 76x said: I've heard a bubba fix would be to put a few split shot fishing weights on the cable by the pedal to change the contact point - anything else? |
That will take some length out of the inner cable, but then you wouldn't have enough travel left to take the carb to full throttle (open). Smoke-um is right about the Edelbrock set-up. I've installed them on several projects, and they work well. Sometimes it takes a while to figure out just the right set-up, but in the end, it works out quite well.
Joel Adams
C3VR Lifetime Member #56
My Link
(click for Texas-sized view!) NCRS
"Money can't buy happiness -- but somehow it's more comforting to cry in a CORVETTE than in a Kia"
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
Lifetime Member
Send PMHot Springs, AR - USA
Joined: 4/24/2004
Posts: 3236
Vette(s): 69 Conv #'s match 427, TKO-600/.64, 3.36HD-Posi, HT, T/T, PS, PB, PW, SP, Leather, Comp XE264HR & Roller Rockers & Lifters, Air-Gap RPM intake, Holley St Av 770 VS, MSD 6AL+Dist+Blaster SS, K&N, Jet-Hot Hooker Side-Pipes, Steeroids, Al Rad, Spal Fans
| Adams' Apple said: That will take some length out of the inner cable, but then you wouldn't have enough travel left to take the carb to full throttle (open). Smoke-um is right about the Edelbrock set-up. I've installed them on several projects, and they work well. Sometimes it takes a while to figure out just the right set-up, but in the end, it works out quite well. |
I concur..
and make sure you adjust the cable to the pedal properly.. ie.. have someone hold the gas pedal to the floor.. hold the carb at WOT.. then adjust the cable back far enough so it barely reaches the carb.. connect it.. make sure its still tight.. then tighten the cable
you may already know this.. but ive seen way too many cars where floored is 1/2 throttle and there is a ton of play in the pedal so I thought I would share this info..
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
Thanks, I'll see what other brackets I can find.
|B|76 X coupe |/B|
#s match - Classic White - Buckskin
|IMG|http://webpages.charter.net/equestrian/76x.gif |/IMG|
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
in Forum: C3 HVAC, Fuel, Emissions, and Exhaust
Sponsored Content