Sponsored Content
Does anyone know what size front sway bar came stock on a 1979 with the standard suspension? Is it 1 inch or is it smaller?
Thanks,
Keith



Be the first to like this post
Sign In to Like this post
Sign In to Like this post
SPONSOR AD:: (Our Sponsors help support Vette Registry)
m
Lifetime Member
Send PMEquinunk, PA - USA
Joined: 10/31/2007
Posts: 2570
Vette(s): 1972 conv, 4-speed, 350, 200hp, numbers match, rally wheels, war bonnett yellow w/white top. good condition, nice driver.
1 inch or BIGGER! 7/8 is pretty small, and is not to resistant to twist. My 72 had a 7/8, I went to 1 1/8. MUCH BETTER control in turns.
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
Lifetime Member
Send PMHot Springs, AR - USA
Joined: 4/24/2004
Posts: 3236
Vette(s): 69 Conv #'s match 427, TKO-600/.64, 3.36HD-Posi, HT, T/T, PS, PB, PW, SP, Leather, Comp XE264HR & Roller Rockers & Lifters, Air-Gap RPM intake, Holley St Av 770 VS, MSD 6AL+Dist+Blaster SS, K&N, Jet-Hot Hooker Side-Pipes, Steeroids, Al Rad, Spal Fans
also.. you should remember that picking a size because that is what was on there isnt ncessarily the best choice.
neither is going overly large.
|UPDATED|3/13/2012 1:08:13 PM (AZT)|/UPDATED|
I always have to think about it so it might be backlwards but the rear sway bar is inversley related to understeer and the front sway is inversely related to oversteer
you can put a giant front bar on and have no oversteer but create understeer. then put a bar on back and still not be balanced. either by not being large enough and still having understeer or by being too large and creating oversteer
the stock sway set (front and rear if included) works for stock engine, stock suspension.
change the shocks, springs, engine weight (aluminum vs iron), and the balance is gone.
|UPDATED|3/13/2012 1:08:13 PM (AZT)|/UPDATED|
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
My '78 with stock standard suspension has a 7/8" sway bar. The Pace car with Gymkhana (FE7) has the 1 1/8" bar. I can't tell much difference if any at all between the 2.
Nice looking '79 ya got there, Keith. I like the color combo. Our picture is on a cruise we took out of Seattle a few years back.
|UPDATED|3/13/2012 5:08:58 PM (AZT)|/UPDATED|
Nice looking '79 ya got there, Keith. I like the color combo. Our picture is on a cruise we took out of Seattle a few years back.
|UPDATED|3/13/2012 5:08:58 PM (AZT)|/UPDATED|
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
Former Member
Send PMManteca, CA - USA
Joined: 11/20/2005
Posts: 3623
Vette(s): 1978,two tone,Metalic Rootbeer & gold
1975 L48 4 speed
Nice tech stuff Ben
.

Jimmy B.
Just can't wait to get on the road again.
Click to see larger views!
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
I put the 1 1/8 on the front of mine, really makes a difference.
(click to see a larger image)
"It Takes A Little Longer To Do It Right"
"It Takes A Lot Longer To Do It Again"
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
in Forum: C3 Engines, Driveline and Handling
Sponsored Content