Sponsored Content
Gold Member
Send PMScotch Plains, NJ - USA
Joined: 1/11/2006
Posts: 247
Vette(s): 1981 Corvette Coupe, Stock, Black on Black,
4 Spd
What started out as a brake component replacement project, I am ending up replacing a lot of other parts too. (1981)
The steering column is out and I want to replace the bearings and other worn out parts (plastic). Does anyone know of articles or forums dealing with this?
Any help will help ! Tanks
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
SPONSOR AD:: (Our Sponsors help support Vette Registry)
Hey Jeff,
How did you get from the brakes to the steering column?
Anyway, here is a good source for lots of stuff.
There is information on steering column. Not sure if it is what you are looking for.
Good luck.
Save the Wave!
Support the National Corvette Museum
Support the National Corvette Museum
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
Gold Member
Send PMScotch Plains, NJ - USA
Joined: 1/11/2006
Posts: 247
Vette(s): 1981 Corvette Coupe, Stock, Black on Black,
4 Spd
Thanks Mr. DW
Well, it's like this, to remove the brake booster I thought it would be necessary to remove the brake and clutch pedal bracket, so, to remove that bracket, I lowered the steering column, the bracket still was not coming out easy, so I removed the steering column. With the column removed the bracket came out easily. Now that the column is out, me being me, I couldn't put it back without replacing the bearings and a paint job.
Hey, I admit it, I got a sickness!
Thanks for the link. I found it. Looks like a good resource for C3 steering issues.
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
I am wanting to replace the bearings in my 77 steering column. were can we get the bearings?
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
Gold Member
Send PMScotch Plains, NJ - USA
Joined: 1/11/2006
Posts: 247
Vette(s): 1981 Corvette Coupe, Stock, Black on Black,
4 Spd
I have looked and find that most of the Vendors have the bearings.
Some have more parts listed than others though and the prices vary too.
See the link from dwright above for help with this.
There are also vendors out there to do the rebuild for you - for $$$.
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
O
You might also check to see if you have a bearing dealer or distributor. Fleck, FAG and other bearing companies can take the bearing and measure it, then find a match to it.
Works great on old Allis-Chalmers tractor bearings.
Works great on old Allis-Chalmers tractor bearings.
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
I need to fix my column. When holding the steering wheel it is wobbly in all directions. Riks corvette sells a kit STE330 51.95, Zip SC-432 55.00. They seem to be the same kit. Here is a link; does this look like it should have the parts necessary any suggestions?
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
Just a little more info. I have 77 late model tilt tele column. I have repaired everything else on the column but its time to fix the woble, I have the exploded view of the column and some good info, i am hoping to get all the parts i will need so when I go to repair it, the car won't be down long
if anyone has been down this road any help will be welcome
Bob
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
in Forum: C3 Engines, Driveline and Handling
Sponsored Content