Sponsored Content
Very nice. I like new stuff. It use to be that all th contacts in the distributor cap were copper but not anymore. A good cap, rotor, and wires make everything better.
Brian - NCM Lifetime Member
73 coupe L48, Flat-top pistons, Performer RPM Heads, Crane Cam and roller rockers, Holley 650 vac sec. Performer intake,
3.55 gear BTO 200-4R trans,
Leather seats, Seatbelt Plus 3point seatbelts, Pioneer CD player
Magnaflow Exhuast System
Dewitt radiator and dual electric fans
Borgeson Steering box
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
SPONSOR AD:: (Our Sponsors help support Vette Registry)
Question on running the spark plug wires:
If they are run parallel for a relatively long distance like suncountry's, is there a risk of the voltage jumping to the adjacent wire and firing the wrong cylinder?
Save the Wave!
Support the National Corvette Museum
Support the National Corvette Museum
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
V
Former Member
Send PMMounds View, MN - USA
Joined: 5/24/2007
Posts: 1034
Vette(s): 70 LT1 coupe, 69 350 HP coupe, 69 390HP 427 coupe, 71 LS5 convert, 85 coupe, 93 coupe
That's the way the factory did it with no problem. If you have a higher voltage ignition system, there is a greater chance of that inductive firing, but not with a factory system.
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
7
Free Member
Send PMYelm, WA - USA
Joined: 7/12/2007
Posts: 356
Vette(s): 1979 L82 4 speed Scat 383 crank 190 cc Procomp Aluminum Heads 202 160 stainless valves GM Powder metal rods Speedpro H860CP Hypereutectic pistons 280 cam hydralic HEI Pro comp 1.6 roller rockers Mighty Demon 750 Sanderson CC1AP Hedders.
I was wondering about the same thing I've seen a lot of pictures of the wires being wrapped or twisted around one another and I thought that was a no no. I was always under the impression you couldn't randomly cross the plug wires or you would get crosstalk from the other wires going on.
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
Lifetime Member
Moderator
Send PMModerator
Moses Lake, WA - USA
Joined: 4/16/2005
Posts: 2134
Vette(s): 1976 L48 4-spd, Mahogany Metalic exterior, Buckskin interior 350ci/350hp, 3rd owner, fiberglass spring, 255/50-16's Torq-Thrust II
[QUOTE=dwright]Question on running the spark plug wires:
If they are run parallel for a relatively long distance like suncountry's, is there a risk of the voltage jumping to the adjacent wire and firing the wrong cylinder?
[/QUOTE]
Dave
I will let you know if I have a cross firing issues once I am up and running. Didn't think it would be an issue as the factory ran all 4 plug wires right next to one another down under the block. But you never know
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
Lifetime Member
Moderator
Send PMModerator
Duncanville, TX - USA
Joined: 11/8/2003
Posts: 22720
Vette(s): #1-1974 L-48 4spd Cp Med Red Metallic/Black deluxe int w/AC/tilt/tele./p/w-p/b/
Am-Fm/map light National/Regional/Chapter NCRS "Top Flight"
#2-1985 Bright Red/Carmine Cp.L-98/auto
Member: NCRS, NCRS Texas, Corvette Legends of Texas
The only wires you really need to watch for are #s 5 & 7...you don't want them running next to each other anywhere in the run. These two plugs fire one right after the other, and are the cylinders that are next to each other. If these two wires run close enough, they will cross-fire. You should always separate these two wires with another wire in between them. If you look closely at any factory plug routing(on mouse engines), you'll see they were run like that...always with another wire in between them. It don't always look good, cosmetically, but the benefits outweigh the cosmetics. 
Joel Adams
C3VR Lifetime Member #56 
My Link 
(click for Texas-sized view!) NCRS
"Money can't buy happiness -- but somehow it's more comforting to cry in a CORVETTE than in a Kia"
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
Lifetime Member
Moderator
Send PMModerator
Moses Lake, WA - USA
Joined: 4/16/2005
Posts: 2134
Vette(s): 1976 L48 4-spd, Mahogany Metalic exterior, Buckskin interior 350ci/350hp, 3rd owner, fiberglass spring, 255/50-16's Torq-Thrust II
Thanks for the tip Joel
, I moved the #5 plug wire in the clamp by the dist which leaves only a couple of inches where #5 & #7 run parallel. If I was to get an induced spark, does it show up under load or at idle?
, I moved the #5 plug wire in the clamp by the dist which leaves only a couple of inches where #5 & #7 run parallel. If I was to get an induced spark, does it show up under load or at idle?Be the first to like this post
Sign In to Like this post
Sign In to Like this post
V
Former Member
Send PMMounds View, MN - USA
Joined: 5/24/2007
Posts: 1034
Vette(s): 70 LT1 coupe, 69 350 HP coupe, 69 390HP 427 coupe, 71 LS5 convert, 85 coupe, 93 coupe
The induced voltage has to jump the spark plug gap, and that is easiest under the least load, so you would most likely see it at idle or during higher RPM deceleration.
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
n
Free Member
Send PMCharleston AFB, SC - USA
Joined: 10/31/2007
Posts: 111
Vette(s): 1979 Cream Beige Coupe w/383 & 700R4
[QUOTE=suncountry]Here is what I am doing
[/QUOTE]
That looks awesome! I dont like the look of my wires running all over the hood, mind telling me what setup you have for the brackets and what wires you got to run them like that?
Thanks!
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
in Forum: C3 Engines, Driveline and Handling
Sponsored Content