Sponsored Content
A
I purchased some Taylor 8mm Spiro Pro Series High Performance Ignition Wires for my 1976 L-48. Well I may sound kinda lame but how do you remove the top part of the distributer cap in order to replace the wires? I do know to replace and match the wires one at a time. Help? 
Aaron 
CLICK HERE to enlarge picture
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
SPONSOR AD:: (Our Sponsors help support Vette Registry)
Are you talking about the plastic piece that keeps the wires from coming off?
If so, then if you look carefully at the top of the distributor. There are two thin latches that pop outward with a flick of your fingernail releasing the wire hold down. I think it may even say "latch" on the top.
GEN III 5.7L "LS6" Engine swap
TKO500 5 spd.
3.54 Dana 44
'69 "N11" Sidepipes
Borgeson Steering Box
Born 8/1981
Sequence #3975
Click here to see more pics of my Vette on CarDomain.
Lifetime Member #26
Borgeson Steering Box
Born 8/1981
Sequence #3975
Click here to see more pics of my Vette on CarDomain.
Lifetime Member #26
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
Lifetime Member
Moderator
Send PMModerator
Duncanville, TX - USA
Joined: 11/8/2003
Posts: 22720
Vette(s): #1-1974 L-48 4spd Cp Med Red Metallic/Black deluxe int w/AC/tilt/tele./p/w-p/b/
Am-Fm/map light National/Regional/Chapter NCRS "Top Flight"
#2-1985 Bright Red/Carmine Cp.L-98/auto
Member: NCRS, NCRS Texas, Corvette Legends of Texas
Yep...the plug wire retaining ring just "snaps" onto the top of the dist. cap. Push outward on the two latches, and it will come up. The wires will also be inserted into the ring, so you'll have to twist/pull them out.
btw...if you look closely at the ring, you'll see that it is numbered at each plug wire hole, so you'll know which wire goes where...as long as the distributer is still in the correct location.Adams' Apple 2007-12-20 06:04:31
btw...if you look closely at the ring, you'll see that it is numbered at each plug wire hole, so you'll know which wire goes where...as long as the distributer is still in the correct location.
Joel Adams
C3VR Lifetime Member #56 
My Link 
(click for Texas-sized view!) NCRS
"Money can't buy happiness -- but somehow it's more comforting to cry in a CORVETTE than in a Kia"
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
7
Free Member
Send PMYelm, WA - USA
Joined: 7/12/2007
Posts: 356
Vette(s): 1979 L82 4 speed Scat 383 crank 190 cc Procomp Aluminum Heads 202 160 stainless valves GM Powder metal rods Speedpro H860CP Hypereutectic pistons 280 cam hydralic HEI Pro comp 1.6 roller rockers Mighty Demon 750 Sanderson CC1AP Hedders.
Aaron don't feel bad! My new HEI distributor didn't have the ring so I had to figure it out. I got a set of the Taylor wires yesterday and I'm not really enjoying making my own wires too much.
79rebuild 2007-12-19 23:26:44
Does anyone have a decent picture of what the plug wires (done up right) at the distributor should look like?
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
79rebuild, the pictures look real good. Looks like your going first class. Do you still have your website covering the restoration? If so what is it? Thanks
Steve, Lifetime Member #129
74 coupe 4 speed 350, 54K actual miles,
all original; paint, interior, engine,
split bumper. #'s match. 2nd owner, no stress cracks.
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
It's looking good Aaron. Nice job.
Save the Wave!
Support the National Corvette Museum
Support the National Corvette Museum
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
Lifetime Member
Moderator
Send PMModerator
Moses Lake, WA - USA
Joined: 4/16/2005
Posts: 2134
Vette(s): 1976 L48 4-spd, Mahogany Metalic exterior, Buckskin interior 350ci/350hp, 3rd owner, fiberglass spring, 255/50-16's Torq-Thrust II
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
A
Glen, Very nice!
Wow shiny, I like shiny things that go fast. Nice wire set up you have there.
Aaron
CLICK HERE to enlarge picture
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
7
Free Member
Send PMYelm, WA - USA
Joined: 7/12/2007
Posts: 356
Vette(s): 1979 L82 4 speed Scat 383 crank 190 cc Procomp Aluminum Heads 202 160 stainless valves GM Powder metal rods Speedpro H860CP Hypereutectic pistons 280 cam hydralic HEI Pro comp 1.6 roller rockers Mighty Demon 750 Sanderson CC1AP Hedders.
Yeah Glen that looks real nice! I see your AC is on already 
Aw I really miss living on the other side of the mountains.
Aw I really miss living on the other side of the mountains. Be the first to like this post
Sign In to Like this post
Sign In to Like this post
A
OK, after driving my Vette through the hood on Saturday it started to run a little ruff while at an idle. So I got out the new plug wires and put them on and cleaned the carb up with some carb cleaner spray. She runs real good now. The retainer ring on top of the distributor cap came off real easy but it is in bad shape and cracked, I did not put it back on, do you have to have it on? One of the old wires I took off had rust on the conection at the distributor cap and the overall wires looked to be real old, probably why it ran ruff. I cleaned all the contacts on the distributor cap before putting new wires on. Next I am planning on getting a new MSD red Distributer cap with built-in Coil and Rotor I found for about $30.00 at Schuck's. The end result is I have a nice bunch of red wires (kinda old school look) in the engine compartment and she runs good.
Aaron1976 2008-02-15 12:51:11
Aaron
CLICK HERE to enlarge picture
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
in Forum: C3 Engines, Driveline and Handling
Sponsored Content