Sponsored Content
Lifetime Member
Send PMHot Springs, AR - USA
Joined: 4/24/2004
Posts: 3236
Vette(s): 69 Conv #'s match 427, TKO-600/.64, 3.36HD-Posi, HT, T/T, PS, PB, PW, SP, Leather, Comp XE264HR & Roller Rockers & Lifters, Air-Gap RPM intake, Holley St Av 770 VS, MSD 6AL+Dist+Blaster SS, K&N, Jet-Hot Hooker Side-Pipes, Steeroids, Al Rad, Spal Fans
i got a plug wire problem... my taylor spiro pros with only about 100 miles on them wont fit between the hooker side pipe headers and the plugs on #1 and #3
so i bought a set of MSD wires ($90 !!!!!) and they wont fit either.
i think i need a plug with a 45 degree angle.
anyone got hooker supercomp side pipe header and a BB and wires that dont touch the pipes on 1 and 3
what kind?
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
SPONSOR AD:: (Our Sponsors help support Vette Registry)
A
When I ordered my Taylor wires (custom fit for your engine) they need to be for cars equipped with headers, that could be the problem. Check with your local speed shop.
Aaron 
CLICK HERE to enlarge picture
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
Free Member
Send PMFrederick, MD - USA
Joined: 9/8/2003
Posts: 3398
Vette(s): 1969 convertible L71 427/435 4-speed black interior
For the life of me I can't remember what company, but one of the big plug wire companies makes plug wires with bendable boots on the plug end, just for this use. Do some searching and you should be able to come up with who makes them.
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
I have Headman Headers on my BB and have the same problem. I bought a set of the heat boots out of the Jegs catalog. They aren't factory equipment but you can at least choose from several colors and they work really well.
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
7
I have a set of MSD wires from Summit and you can bend the boots to fit
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
P
Accell used to make "shortie" header spark plugs just for that problem and if I remember right, they also came with the washers to index the electrode to the intake valve.......Bill
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
Lifetime Member
Send PMHot Springs, AR - USA
Joined: 4/24/2004
Posts: 3236
Vette(s): 69 Conv #'s match 427, TKO-600/.64, 3.36HD-Posi, HT, T/T, PS, PB, PW, SP, Leather, Comp XE264HR & Roller Rockers & Lifters, Air-Gap RPM intake, Holley St Av 770 VS, MSD 6AL+Dist+Blaster SS, K&N, Jet-Hot Hooker Side-Pipes, Steeroids, Al Rad, Spal Fans
The bendable boots are MSD... still not alot of room... id like to use MSD wires are my tach and coil are MSD.
does anyone have and BB and hooker side pipe headers? either the 90 degree wires or the bendable *could* work.
anyone using either one of these?
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
7
Mine has a big block and Hooker headers and the MSD wires work fine
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
P
Lifetime Member
Send PMApache Junction, AZ - USA
Joined: 10/15/2006
Posts: 285
Vette(s): 1982,150K,Renegade CFI,Hooker Side Pipes,85 fuel pump,Bilsteins,HD suspension, Aluminum radiator, SharkBar/w 5-Point Restraints. 3:73 gears coming soon.
I had the same problems even with the MSD flex boots. I now use Accel wires and use the 45 degree boots on 4 of the 6 plugs. I also use the heat shield sleeves that connect at the plugs which help but one still need to do some good quality wire routing to keep them off the headers.
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
t
I ahve hooker headers on my 76, installed moroso wires no problems
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
in Forum: C3 Engines, Driveline and Handling
Sponsored Content