Vette Registry | Lowering front end - Forums

Vette(s): 1979 L82 4 speed Scat 383 crank 190 cc Procomp Aluminum Heads 202 160 stainless valves GM Powder metal rods Speedpro H860CP Hypereutectic pistons 280 cam hydralic HEI Pro comp 1.6 roller rockers Mighty Demon 750 Sanderson CC1AP Hedders.

I see the 550lb springs are an inch shorter but I don't think the ride height is affected. You might be looking at the adjustable coil over over some other suspension mod. I seen a 79 at the swap meet just recently and his was low. He had the VB&P suspension kit on it. Why do you want to lower the front?

Be the first to like this post
Sign In to Like this post

Lowering front end

Posted: 4/12/08 10:42pmMessage 3 of 14

Reply Quote

DaveM

Lifetime Member

Send PM

Flanders, NJ - USA

Joined: 1/27/2004

Posts: 2556

Vette(s): 1982 Black, ZZ4, Hooker Side Pipes, 3.55 Rear, Rebuilt & upgraded 700R4, All new suspension, brakes, & new Charcoal interior.

I put the 550lbs. springs in my car and the front is higher than it was before.

Dave

Lifetime Member #116
Dave's '82

Be the first to like this post
Sign In to Like this post

Lowering front end

Posted: 4/13/08 5:22amMessage 4 of 14

Reply Quote

Lynne73

Former Member

Send PM

Easton, PA - USA

Joined: 11/6/2003

Posts: 232

Vette(s): 1973 Coupe 350 Auto.T-Tops L48,65450 miles.

You could take your coils out and cut 1 ring off. Be sure to use a cut off wheel, not a torch. Go to a Spring Shop the have catalogs for all spring heights, inside, outside diameters, spring rates and wire size.

Dave- Lynne 73

Be the first to like this post
Sign In to Like this post

Lowering front end

Posted: 4/13/08 6:26amMessage 5 of 14

Reply Quote

73 Blue Ray

Former Member

Send PM

Joined: 3/22/2008

Posts: 13

Last year I put a ZZ-4 in and my front end was higher than I liked, so I did what Dave suggested, I cut off one ring from my springs. It took 5 metal cutting blades and a sawsall but I finally got them cut. phew

A cut off wheel maybe easier!! My car does look better and I still hope it will settle even a little more and look even better. Good luck Smile

Be the first to like this post
Sign In to Like this post

Lowering front end

Posted: 4/13/08 9:38amMessage 6 of 14

Reply Quote

hvb79

Former Member

Send PM

Renton, WA - USA

Joined: 4/12/2008

Posts: 21

Vette(s): 1979 - Light Custom - Lamborghini Orange

For some reason, the front end on my car is slightly higher and I would like its stance better if it was lowered a bit.

Be the first to like this post
Sign In to Like this post

Lowering front end

Posted: 4/13/08 9:39amMessage 7 of 14

Reply Quote

hvb79

Former Member

Send PM

Renton, WA - USA

Joined: 4/12/2008

Posts: 21

Vette(s): 1979 - Light Custom - Lamborghini Orange

Thanks for the advice.

Did the shortening of the coil affect the ride a all?

Be the first to like this post
Sign In to Like this post

Lowering front end

Posted: 4/13/08 11:34amMessage 8 of 14

Reply Quote

79rebuild

Free Member

Send PM

Yelm, WA - USA

Joined: 7/12/2007

Posts: 356

Since your local you can give these guys a shout, Right Way Spring Co 2545 Jefferson Avenue, Tacoma Wa, I had them put new cushions and bands on my leafs. The guy there was smart, knew a lot about vette's too. I may have to do the same thing if mine don't settle down, It's sitting a little high in the front with the new engine, but I just put it all back together new shocks etc..so I want to see if mellow out a little.

Be the first to like this post
Sign In to Like this post