Sponsored Content
d
I am ordering a new HEI distributor to replace my stock HEI on a 1976 L48.
The new unit produces a 45,000 volt spark.
Does anyone know what the volt spark is on the stock distributor?
Dan
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
SPONSOR AD:: (Our Sponsors help support Vette Registry)
40,000 volts with the standard HEI.
The advantage is not the voltage, that's trivial. But instead the MSD creates a much longer spark duration that allows the fuel to better light in the cylinder.
With my 75 on a dyno, the exhaust would burn your eyes. With the MSD installed the same dyno test, the exhaust was clean, and breathing was easy. It did not improve power at that point, but that was due to the engine limitations. With more mods to the engine I am sure the MSD was part of the answer.
MSD stands for Multiple Spark Discharge. What it does instead of just one continous spark, it fires the plug, stops the spark,and fires it again. At low rpm it may do this up to 5 or 6 times. As the rpm increases the number of times decreases due to the fact the cylinders must fire much closer together and in a shorter time span.
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
d
Thanks for the detail...
It is very heplful!
Dan
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
d
The unit I had intended to order was from Mallory.
It is their Mallory 85 Series HEI Distributor.
Will it match the MSD?
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
That is the distributor I use and the MSD 6 comes with all you need to hook it up to the HEI system.
"I Love the Infantryman he is the underdog. They are the wind, the rain, and the mud boys. They give up all comforts and necessities and in the end they are the ones the war cannot be won with out!" Ernest Pyle
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
K
Just a heads up;
I went with the Mallory on my '79 last spring and I'm dissapointed as heck with it!
I have had to replace the ignition module on it twice after a grand total of 2,000 miles.
I'm going to spend the big bucks on the MSD as soon as I'm able to.
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
g
Lifetime Member
Send PMIrving, TX - USA
Joined: 8/21/2004
Posts: 4286
Vette(s): #1 -1969 Corvette Coupe Riverside Gold, black interior,MN,A/C,350/350,PS,PB,window cranks.
#2 -2000 C5, black/black, 6 sp, Bose system & lots of buttons.
[QUOTE=KDADDY79]Just a heads up;
I went with the Mallory on my '79 last spring and I'm dissapointed as heck with it!
I have had to replace the ignition module on it twice after a grand total of 2,000 miles.
I'm going to spend the big bucks on the MSD as soon as I'm able to.
[/QUOTE]
Same here too! Same happened to me. So I took that crappy puppy off and stuck the original distributor back on with Pertronics. Works PERFECT now and NO PROBLEMS. 
Just my 2 pennies worth..
Just my 2 pennies worth..
�����
My Link 
MICK - C3VR Lifetime Member #113
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
r
I installed an MSD with the Sparkbox on my '81. Never had any problems so far. I installed the sparkbox out of sight in order to keep as much of the stock look as possible.
Jim
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
w
I have a Mallory Magnetic Dist & spark box No problems at all. Car runs great !
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
in Forum: C3 Engines, Driveline and Handling
Sponsored Content