Sponsored Content
Hi all, I have a 1980 Corvette was pulling very hard to the left. Put all new brake, calipers and wheel bearings. It still pulled to the left. Put on new tires and had it lined up. STILL PULLS to the left. Any ideas?
Thanks J
Thanks J
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
SPONSOR AD:: (Our Sponsors help support Vette Registry)
m
Lifetime Member
Send PMEquinunk, PA - USA
Joined: 10/31/2007
Posts: 2570
Vette(s): 1972 conv, 4-speed, 350, 200hp, numbers match, rally wheels, war bonnett yellow w/white top. good condition, nice driver.
What about the right rear emergency/brake pads being loose or dragging?
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
Did you lift the front of the car and see if the left wheel is difficult to turn? If so it could need a brake hose. They can fail inside and create a restriction.
If not, was a COMPLETE inspection done on the front end. It may be in aligh sitting still, but have a bad bushing or component that sits in a normal position but flexes an shifts position under rolling load. Control arm bushings will do this. ( upper or lower )
Dont forget the power steering valves. You could take the belt off and take a short drive. It will be hard to steer, but if the pull stops it is a power steering issue.
What about the rear suspension and alignment? The rear can easily cause a problem in the front when the front is in good shape.
|UPDATED|6/2/2015 5:48:40 AM (AZT)|/UPDATED|
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
Look up the power steering "centering" procedure. Might be going bad or needs adjustment.
Only 34 years together
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
kstyer said:
Did you lift the front of the car and see if the left wheel is difficult to turn? If so it could need a brake hose. They can fail inside and create a restriction.
If not, was a COMPLETE inspection done on the front end. It may be in aligh sitting still, but have a bad bushing or component that sits in a normal position but flexes an shifts position under rolling load. Control arm bushings will do this. ( upper or lower )
Dont forget the power steering valves. You could take the belt off and take a short drive. It will be hard to steer, but if the pull stops it is a power steering issue.
What about the rear suspension and alignment? The rear can easily cause a problem in the front when the front is in good shape.
Ken, it's nice to see you back in the ball game.....We haz been beating Joel to pieces.....
ebo
eboBe the first to like this post
Sign In to Like this post
Sign In to Like this post
Lifetime Member
Moderator
Send PMModerator
Duncanville, TX - USA
Joined: 11/8/2003
Posts: 22714
Vette(s): #1-1974 L-48 4spd Cp Med Red Metallic/Black deluxe int w/AC/tilt/tele./p/w-p/b/
Am-Fm/map light National/Regional/Chapter NCRS "Top Flight"
#2-1985 Bright Red/Carmine Cp.L-98/auto
Member: NCRS, NCRS Texas, Corvette Legends of Texas
Is this something that just started, or have you been fighting this for a while?
Ken hit the most likely causes(brakes/alignment), and John was right in checking the power steering control valve adjustment.
You can check that by lifting the front tires off the ground, and starting the engine with the steering wheel in the straight ahead position. DO NOT reach thru the steering wheel to start the engine from outside the car!! If it IS the p/s adjustment, and you do start it from outside like that, you could wind up with a broken wrist!! Sit in the car, and leave your hands(face/hair/etc) OFF of the wheel to start the engine. If the steering jumps to the left by itself, the control valve needs to be adjusted. There are a couple of threads here with info on how that is done, if you do not have the Factory Service Manual.
Does the car sit level at all 4 corners? A sagging spring(or springs) can sometimes cause a pull if it's bad enough to effect the alignment.
|UPDATED|6/2/2015 10:15:15 AM (AZT)|/UPDATED|
Ken hit the most likely causes(brakes/alignment), and John was right in checking the power steering control valve adjustment.
You can check that by lifting the front tires off the ground, and starting the engine with the steering wheel in the straight ahead position. DO NOT reach thru the steering wheel to start the engine from outside the car!! If it IS the p/s adjustment, and you do start it from outside like that, you could wind up with a broken wrist!! Sit in the car, and leave your hands(face/hair/etc) OFF of the wheel to start the engine. If the steering jumps to the left by itself, the control valve needs to be adjusted. There are a couple of threads here with info on how that is done, if you do not have the Factory Service Manual.
Does the car sit level at all 4 corners? A sagging spring(or springs) can sometimes cause a pull if it's bad enough to effect the alignment.
|UPDATED|6/2/2015 10:15:15 AM (AZT)|/UPDATED|
Joel Adams
C3VR Lifetime Member #56 
My Link 
(click for Texas-sized view!) NCRS
"Money can't buy happiness -- but somehow it's more comforting to cry in a CORVETTE than in a Kia"
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
Thanks so much for all the input. Looks like a got a few things to check. I'll let you know what I find out.
Thanks again all!!!!
Thanks again all!!!!
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
in Forum: C3 Engines, Driveline and Handling
Sponsored Content