Sponsored Content
V
IHAVE READ ALL THE POST REGARDING THIS SITUATION. HOWEVER, MINE IS ALITTLE DIFFERENT. WHILE ADJUSTING THE HOOD I INSTALLED THE DRIVERS SIDE LATCH PIN (SPEAR), I CLOSED THE HOOD TO SEE IF IT WOULD LATCH AND IT DID , THEN I COULD NOT GET IT TO OPEN. THE CABLES ARE WORKING FINE AND THE LATCHES RELEASE. MY PROBLEM IS THE STRIKE SPEAR IS CAUGHT IN THE LATCH. THERE IS A LIP ON THE BOTTOM OF IT AND IT WON`T RELEASE FROM THE LATCH, IT GETS CAUGHT.
PULLING ON THE CROSS CABLE DOESN`T RELAESE IT. NOR DOES PUSHING THE MAIN HOOD CABLE LATCH. 
ANYONE HAVE AN IDEA. I`M GOING TO RAISE THE CAR TO SEE IF I CAN ACCESS THE SPEAR FROM THE UNDERNEATH. AFTER THAT I`M OUT OF IDEAS. FREAH POINT OF VIEW WOULD BE WELCOME, THANKS, BOB
ANYONE HAVE AN IDEA. I`M GOING TO RAISE THE CAR TO SEE IF I CAN ACCESS THE SPEAR FROM THE UNDERNEATH. AFTER THAT I`M OUT OF IDEAS. FREAH POINT OF VIEW WOULD BE WELCOME, THANKS, BOBBe the first to like this post
Sign In to Like this post
Sign In to Like this post
SPONSOR AD:: (Our Sponsors help support Vette Registry)
Have you tried pushing down on the hood - directly over the spear while pulling on the release - maybe this could free up the %$#&^% thing and it will pop up - just a thought - perhaps if you can push up from the bottom on the spear - while the cable is pulled - Please let us know what happens
WOW
Big Al
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
Lifetime Member
Moderator
Send PMModerator
Duncanville, TX - USA
Joined: 11/8/2003
Posts: 22720
Vette(s): #1-1974 L-48 4spd Cp Med Red Metallic/Black deluxe int w/AC/tilt/tele./p/w-p/b/
Am-Fm/map light National/Regional/Chapter NCRS "Top Flight"
#2-1985 Bright Red/Carmine Cp.L-98/auto
Member: NCRS, NCRS Texas, Corvette Legends of Texas
You might try pushing sideways in both directions on the hood while someone pulls on the cable.
You might have someone push down on the front of the hood while you pull the cable.
You might try pushing down on the center/edge(mid-way between the latch and the headlight area) of the hood, while pulling up on the corner that is stuck.
If all else fails, lay a folded towel on the hood above the latch, and have someone pull the cable, while you beat down on the towel, with the flat of your hand, or a fist. Sometimes, the bouncing motion like this will be enough to pop the latch around the spear, and let it pass the lip.
Jacking the front of the car, from the center of the front cross member, might just move the body enough to release the latch, depending on which way it is too far out of adjustment. It might also make it even tighter...
If that happens, try jacking it up from the frame behind the front wheels...this will let the front of the body "sag" a little...
Good luck. Hope ya get it open.
You might have someone push down on the front of the hood while you pull the cable.
You might try pushing down on the center/edge(mid-way between the latch and the headlight area) of the hood, while pulling up on the corner that is stuck.
If all else fails, lay a folded towel on the hood above the latch, and have someone pull the cable, while you beat down on the towel, with the flat of your hand, or a fist. Sometimes, the bouncing motion like this will be enough to pop the latch around the spear, and let it pass the lip.
Jacking the front of the car, from the center of the front cross member, might just move the body enough to release the latch, depending on which way it is too far out of adjustment. It might also make it even tighter...
If that happens, try jacking it up from the frame behind the front wheels...this will let the front of the body "sag" a little...
Good luck. Hope ya get it open.
Joel Adams
C3VR Lifetime Member #56 
My Link 
(click for Texas-sized view!) NCRS
"Money can't buy happiness -- but somehow it's more comforting to cry in a CORVETTE than in a Kia"
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
V
YEAH, I`M IN PROCESS OF ALL OF THAT, i HAVE ALOT OF MOVEMENT BUT IT WONT RELEASE,. THANKS JOEL
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
V
WHAT A BALL BUSTER!!!
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
g
Lifetime Member
Send PMTemperance, MI - USA
Joined: 10/18/2004
Posts: 275
Vette(s): 1977 Corvette Orange T-Top
2003 50th Anniv. roadster
Hey Bob, If all else fails take a crowbar in each side near the catch and pry like crazy!!!! 
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
V
IT MAY JUST COME TO THAT!!!
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
7
Mine did the same and we were able to get a socket with enough length and swivels to loosen the latch on the hood portion. Mine probably has better access though having the eggcrate sides but you may be able to do it from underneath. It is really frustrating!
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
Lifetime Member
Send PMGreensburg, IN - USA
Joined: 9/24/2003
Posts: 5387
Vette(s): Previous: 1984 Coupe, 1988 Maroon Coupe, 1989 Coupe, 2001 Roadster Present: 1967 Stingray Roadster, 1976 Stingray Coupe, 1989 Roadster..
Bob if you get it upin the air can yo take something like a cane (it has a nice rubber tip & a handle) and push up in the general area of the latch?
Everyone else was pushing down (closed) I thought I might head in the open position...
Everyone else was pushing down (closed) I thought I might head in the open position...
Tuxblacray: She's Back In Black! Check out my pics @ My Link 
(Click on image to see a bigger version)
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
V
UNJAMMED AND OPEN, THANKS TO ALL FOR THE INPUT. aFTER TRYING ALL OF THOSE AND SOME MORE OF MY OWN, WE DETERMINED THAT I HAD TO LOOSE THE DRIVER SIDE HINGE BOLTS AT THE FRONT OF THE CAR. A LONG SKINNY ARMED FRIEND OF MINE WAS ABLE TO REACH UP THROUGH THE OPEN GRILL AND LOOSEN THE BOLTS. a SMALL JIGLLE TOWARD THE WINDSHEIL AND OPEN SHE CAME. WHAT A PIA. DETERTMINED THAT MY CABLES WERE A BIT WORN TO SO I BOUGHT NEW ONES AND WILL REPLACE BEFORE I ATTEMPT TO ADJUST AGAIN.
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
in Forum: C3 Electrical, Body and Interior
Sponsored Content