Sponsored Content
7
Hello
My hood is stuck in a weird way.
When I pull the handle, both sides pop out but the driver side is still stuck. It does pop up, but it is still being held by mysterious forces.
I enlisted my wife to keep the handle pulled while I wrestle it, but to no avail.
I'm a bit at a loss here. I see the access hole (if I pop the plug out), but what's next even if I do that. I wouldn't know what to pull/push with a wire. The service manual/Haynes/assembly manual did not help me much.
It would be worth mentioning that I removed my hood a while ago and when I put it back, it was not aligned by 1/8" to 1/4". Kind of tilting right to left.
Any suggestions? I do have a hacksaw, but would like to avoid it.
Thanks!
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
SPONSOR AD:: (Our Sponsors help support Vette Registry)
Is the front of the hood binding on the body?
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
7
Hood is not binding on the body. There is a gap/spacing all around, just not even as it should. The nose part might rub a tad.
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
Can you see for sure that the latch is actually released, can you get one more set of hands.... One holding the cable release latch, one pulling the hood to the off side and one pushing toward that off side. Maybe it is just cocked to one side as you described?
ebo
|UPDATED|12/1/2014 10:29:18 AM (AZT)|/UPDATED|
eboBe the first to like this post
Sign In to Like this post
Sign In to Like this post
Lifetime Member
Send PMLemon Grove, CA - USA
Joined: 10/17/2007
Posts: 2041
Vette(s): 1982 C3 Collectors Edition 44000 miles, sat in the sun most of its life, My wife purchased it for me for Father's Day in 2007 from her girlfriend that had it for 19 years. It is on the road again. I'm retired but it is now my daily driver.
If what ebo says does not work. I saw a thread on making a tool and how to use it to pop the hood. I'm thinking it was on this forum about 3-4 years ago.
Let us know if you need some help researching it. It could have been a Google or the Collector forum also. Just let me know and I can try to retrace my steps if nothing else works.
I just do not want to go through that work if you can Ebo it open.
Let us know if you need some help researching it. It could have been a Google or the Collector forum also. Just let me know and I can try to retrace my steps if nothing else works.
I just do not want to go through that work if you can Ebo it open.
1 person likes this post
Sign In to Like this post
Sign In to Like this post
Lifetime Member
Moderator
Send PMModerator
Duncanville, TX - USA
Joined: 11/8/2003
Posts: 22714
Vette(s): #1-1974 L-48 4spd Cp Med Red Metallic/Black deluxe int w/AC/tilt/tele./p/w-p/b/
Am-Fm/map light National/Regional/Chapter NCRS "Top Flight"
#2-1985 Bright Red/Carmine Cp.L-98/auto
Member: NCRS, NCRS Texas, Corvette Legends of Texas
IF the hood has popped up on both sides, pulling the latch is a waste, since it has already released the latches on both sides. What has prolly happened is that since the hood is shifted to one side, it is hanging on the cone spring of the male part of the latch. Try pushing DOWN slightly on that side while also pushing the hood side-to-side, and then lifting. It's a ballet of movements, but it sounds harder to do than it actually is. Once you get it open, adjust the hood properly, so this won't happen again(theoretically, that is...).
Joel Adams
C3VR Lifetime Member #56 
My Link 
(click for Texas-sized view!) NCRS
"Money can't buy happiness -- but somehow it's more comforting to cry in a CORVETTE than in a Kia"
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
Yea, unlatched, I can move the aft edge of my hood back and forth about a quarter of an inch (slop in the hinges I guess).
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
7
Joel's description of what "prolly" happened is most likely right-on, since both sides do pop when I pull the release, just that one side is still stuck somehow.
Can't wait to try this later tonight.
Stay tuned for updates and thanks for all the replies.
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
Adams' Apple said: IF the hood has popped up on both sides, pulling the latch is a waste, since it has already released the latches on both sides. What has prolly happened is that since the hood is shifted to one side, it is hanging on the cone spring of the male part of the latch. Try pushing DOWN slightly on that side while also pushing the hood side-to-side, and then lifting. It's a ballet of movements, but it sounds harder to do than it actually is. Once you get it open, adjust the hood properly, so this won't happen again(theoretically, that is...).
So glad I got you on the right track...... brother Joel!
So think you'll see snow for xmas............???
ebo
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
Steph..... please don not say hack saw and Corvette in same sentence...... ;)
Good Luck,
ebo
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
in Forum: C3 Electrical, Body and Interior
Sponsored Content