Sponsored Content
2
How difficult to remove the inside door panels 73 vert. I need to adjust the windows as they don't line up well when door shut and putting the window up. I thought I saw a post sometime for window alignment.. Also makes some noise. May need some lube on the track.
By the way.. any suggestions on reference material (CD/Book etc)for working on a 73 vette? want to be Vette specific.
By the way.. any suggestions on reference material (CD/Book etc)for working on a 73 vette? want to be Vette specific.
Lifetime Member #86
USN 1966-1970
WestPac 67-68 Tet I&II
Featured in Corvette Enthusiast Aug 2007 "Shark Attack"
Blue Green *** 454,4 Spd, Dark Saddle Leather, A/C, AM-FM St. (orig), PW, Tilt -Tele Wheel"
(click to see a bigger image)
USN 1966-1970
WestPac 67-68 Tet I&II
Featured in Corvette Enthusiast Aug 2007 "Shark Attack"
Blue Green *** 454,4 Spd, Dark Saddle Leather, A/C, AM-FM St. (orig), PW, Tilt -Tele Wheel"
(click to see a bigger image)
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
SPONSOR AD:: (Our Sponsors help support Vette Registry)
B
Lifetime Member
Send PMFrederick, MD - USA
Joined: 2/20/2003
Posts: 555
Vette(s): Frederick County Corvette Club (Maryland)
Tan 64 365 Hp Conv 4 sp
Red 72 4 sp Conv ..running a '68 327
Blue 76 Coupe L 48 4 sp
White 79 Coupe L 82 auto
Silver 98 Conv, 6 sp
35th Anniv '88 vette
EXTREMELY EASY..... ONLY "special" Tool you really should have is the tool to remove the spring clip that holds the window crank handle. Other then that a simple screw driver ....
Playing around with adjusting the window is about 10 times as hard as removing the door panel... also a lot more fun... LOL
A Factory Service Manuel and an Assambly manuel should take care of what you need...
Enjoy....
Bob
Bob
64,72 & 98 Corvette Ragtops
76 & 79 & qa 88 ANC Corvette Coupes 
Click on any image for larger view!
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
2
I have power windows so that should eliminate that prob.. are there clips behind the panels or are they just held on with screws? I've taken other (car) door panels off with the barbed clips and they could prove difficult.Had to be extra careful...
Ray
Ray
Lifetime Member #86
USN 1966-1970
WestPac 67-68 Tet I&II
Featured in Corvette Enthusiast Aug 2007 "Shark Attack"
Blue Green *** 454,4 Spd, Dark Saddle Leather, A/C, AM-FM St. (orig), PW, Tilt -Tele Wheel"
(click to see a bigger image)
USN 1966-1970
WestPac 67-68 Tet I&II
Featured in Corvette Enthusiast Aug 2007 "Shark Attack"
Blue Green *** 454,4 Spd, Dark Saddle Leather, A/C, AM-FM St. (orig), PW, Tilt -Tele Wheel"
(click to see a bigger image)
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
Lifetime Member
Moderator
Send PMModerator
Duncanville, TX - USA
Joined: 11/8/2003
Posts: 22720
Vette(s): #1-1974 L-48 4spd Cp Med Red Metallic/Black deluxe int w/AC/tilt/tele./p/w-p/b/
Am-Fm/map light National/Regional/Chapter NCRS "Top Flight"
#2-1985 Bright Red/Carmine Cp.L-98/auto
Member: NCRS, NCRS Texas, Corvette Legends of Texas
Phillips screw holds the door handle on, and one at the front and rear top of the panel. Also frt & rear about midway down. The rest is held on with plastic "velcro" pieces. Not really hard at all. The good stuff is trying to get the winder(or window for you non-Texans 
)adjusted so it goes up and seals on the weatherstrip on the top. (Make sure the top is up) By all means, get a factory repair manual. You can find them at swap meets for around $40. Have fun!! 
)adjusted so it goes up and seals on the weatherstrip on the top. (Make sure the top is up) By all means, get a factory repair manual. You can find them at swap meets for around $40. Have fun!! Joel Adams
C3VR Lifetime Member #56 
My Link 
(click for Texas-sized view!) NCRS
"Money can't buy happiness -- but somehow it's more comforting to cry in a CORVETTE than in a Kia"
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
M
Former Member
Send PMSan Antonio, TX - USA
Joined: 9/8/2003
Posts: 117
Vette(s): 1973 Corvette Roadster
Elkhart Green, 300hp 4-spd // 2003 Millinium Yellow Coupe
You can also adjust the bump stops on the winders (I'm from Texas)while you have the door panels removed. You might even want to replace them, thier cheap.
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
2
Thanks for the tips... I will try that job during the holidays... think I will get athe sjhop manual first. 
Lifetime Member #86
USN 1966-1970
WestPac 67-68 Tet I&II
Featured in Corvette Enthusiast Aug 2007 "Shark Attack"
Blue Green *** 454,4 Spd, Dark Saddle Leather, A/C, AM-FM St. (orig), PW, Tilt -Tele Wheel"
(click to see a bigger image)
USN 1966-1970
WestPac 67-68 Tet I&II
Featured in Corvette Enthusiast Aug 2007 "Shark Attack"
Blue Green *** 454,4 Spd, Dark Saddle Leather, A/C, AM-FM St. (orig), PW, Tilt -Tele Wheel"
(click to see a bigger image)
Be the first to like this post
Sign In to Like this post
Sign In to Like this post
in Forum: C3 Electrical, Body and Interior
Sponsored Content